 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| Interlock Switches Guard Locking Switches Centurion Specifications Standards EN954-1, ISO13849-1, IEC/EN60204-1, NFPA79, EN1088, ISO14119, IEC/ EN60947-5-1, ANSI B11.19, AS4024.1 Cat. 1 Device per EN954-1 Dual channel interlocks suitable for Cat. 3 or 4 systems CE marked for all applicable directives, cULus, BG, and SUVA 2 N.C. direct opening action AC15 500V 250V 100V 1A 2A 5A 250V 0.5A 24V 2A 500V/500VA 10A 5V 5mA >2mm (0.078in) (Ui) 500V (Uimp) 2500V 1 N.C. 2mm (0.078in) Heavy duty die cast alloy Stainless Steel IP66 1 x M20 or quick disconnect -25C to +80C (-10F to +176F) 2 x M4 1,000,000 operations 1,000,000 operations 500g (1.20lbs) Red Category Approvals Safety Contact Designation/Utilization Cat. AC (Ue) (Ie) DC 73013 Description The Centurion is a positive mode, thumbwheel operated machine guard locking interlock switch that locks the guard closed until the operator manually rotates the thumbwheel, retracting the shaft from the guard door. The action of retracting the shaft initiates two functions; it isolates the power to the machine while the guard is open and, due to the operating principle, gives up to 20 seconds delay before the guard can be opened. Alternative styles with longer shafts can increase the time delay by as much as 50%. The Centurion is ideal for use on simple machines with short, constant run down times. It is important that correct installation and operation of the unit are followed to ensure that the retractable shaft cannot be extended when the guard is open. For machines with long or variable run down times or where frequent access is required, solenoid locking switches such as the TLS-GD2 and Atlas 5 should be considered. The Centurion has 2 safety (N.C.) contacts, 1 auxiliary (N.O.) contact and 1 conduit entry (either M20 or quick disconnect). EX and Pneumatic styles of the Centurion are also available; see the Explosion Proof section on page 16-1 for more information. Note: Additional safety measures (i.e., a shroud) should be used to ensure the thumbwheel can only be accessed by fingertips. Max Switched Current/Volt/ Load Thermal Current (lth) Min Current Safety Contact Gap Rtd. Insulation Voltage Rtd. Impulse withstand Volt Auxiliary Contacts Shaft Movement to Achieve Contact Operation Case Material Locking shaft Protection Conduit Entry Operating Temperature Mounting Mechanical Life Electrical Life Weight Colour Note: The safety contacts of the Guardmaster switches are described as normally closed (N.C.) i.e., with the guard closed, actuator in place (where relevant) and the machine able to be started. Features * * * * Manually operated time delay, allows for machine run down Simple operation & installation Robust die cast housing, ideal for heavy duty applications Contacts, 2 N.C. & 1 N.O. (sealed to IP66) Centurion Thumbwheel Operation Interlocking shaft is manually retracted from the guard by rotating the thumbwheel. 3-40 Interlock Switches Guard Locking Switches Centurion Product Selection Catalogue Number Safety Contacts Auxiliary Contacts BBM/MBB Type Right Hand 2 N.C. 1 N.O. BBM Left Hand Right Hand Extended Bolt Left Hand Extended Bolt M20 Conduit 440K-B04025 440K-B04026 440K-B04039 440K-B04040 Quick Disconnect 440K-B04046 440K-B04047 440K-B04048 440K-B04049 Recommended mating cable, 2m (6.5ft). See page 15-10 for details and additional lengths. 889D-F8AB-2 Approximate Dimensions--mm (inches) Dimensions are not intended to be used for installation purposes. View from End View from Rear 14 (0.55) O 20 (0.79) 24 (0.94) 35 (1.38) View from Side 16.5 (0.65) 98 (3.86) 86 (3.39) 36 (1.42) 15 (0.59) 6 (0.24) O14 (0.55) 30 (1.18) 64 (2.52) 6 (0.24) RH Style Front View LH Style Front View 40.5 (1.59) Typical Wiring Diagrams Safety Circuit 1 Safety Circuit 2 Auxiliary 33 34 11 21 22 12 2 N.C. + 1 N.O. Connector Pinout 1 7 Terminal 11 12 21 22 33 34 Ground Contact N.C. Contact Action Contact Open Contact Closed Actuator withdrawal distance from full insertion 2 N.C. + 1 N.O. (BBM) 1 2 3 8 4 7 6 5 6 5 4 3 8 N.C. N.O. 24.5 11/12 21/22 33/34 2 0mm 3-41 |
Price & Availability of 440K-B04026
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |